/themes/my_demo/public/assets/images/s24w1.png

A3002RU-V2


- Complies with the IEEE 802.11ac Wave 2 Wi-Fi standard.

- 1167Mbps in total on dual band, 867Mbps on 5GHz and 300Mbps on 2.4GHz 

- MU-MIMO technology allows to transfer data to multiple devices at the same time, each device enjoys high Internet speed separately.

- Beamforming technology allows to intensively transmit the signal to the directions of the other wireless connected terminals, improving the --using-efficiency of the bandwidth and reducing the dead spots and the surrounding unnecessary RF interference.

- Full gigabit ports offers a larger capability for data streaming via cable connection.

- Supports DHCP, Static IP, PPPoE, PPTP and L2TP connection mode.

- Provides 64/128-bit WEP, WPA, and WPA2 encryption.

- QoS function allows to change the bandwidth for different terminals via IP address.

- Supports IP address filtering, port filtering, MAC filtering, URL filtering and port forwarding. 

- Multiple SSIDs allows to create different SSIDs for different groups, better for Internet access management.

- Smart UI design is easy for the users to finish the basic configuration with their cellphones.


Hardware

Interface


- 4 *1000Mbps LAN Adaptive Ports

- 1 *1000Mbps WAN Adaptive Port

- USB 2.0 Port

Power Supply - 12V DC/1A
Button

- 1 *RST/WPS Button, 

- 1* Power On/Off Button

LED Indicator

- 1 * SYS   

- 1 * 2.4G   

- 1 * 5G    

- 1 * WAN    

- 4 * LAN    

- 1 * USB

Antenna

- 2 * 2.4GHz fixed antennas(5dBi)

- 2 * 5GHz fixed antennas(5dBi)

Dimensions (L x W x H)

 210 x 120 x 40mm (not including antennas)

 

Wireless

Standards

- IEEE 802.11ac, 

- IEEE 802.11n, 

- IEEE 802.11g, 

- IEEE 802.11b, 

- IEEE 802.11a

RF Frequency

- 2.4GHz/5GHz

Data Rate

- 2.4GHz: Up to 300Mbps

- 5GHz: Up to 867Mbps

EIRP

- 2.4GHz < 20dBm 

- 5GHz < 20dBm 

Wireless Security

-64/128-bit WEP, WPA and WPA2

Reception Sensiticity

- 2.4G:11b 11M:-81dBm@8% PER

          11g 54M:-68dBm@10% PER

          11n HT20 MCS7:-65dBm@10% PER   

                 HT40 MCS7:-62dBm@10% PER


- 5G: 11a 54M:-68dBm@10% PER

         11n HT20 MCS7:-65dBm@10% PER    

                HT40 MCS7:-62dBm@10% PER

         11ac VHT80 MCS9:-51dBm@10% PER


 

Software

Operation Mode

- Gateway Mode        

- Repeater Mode

- AP Mode                  

- WISP Mode

Status

- WAN                       

- Wireless                     

- LAN

- System Information

Network

- WAN Setting             

 - LAN Setting               

- IPTV  Setting

- DHCP&ARP Tables   

- Static Route              

- Routing Table

WAN Type

- Static IP, 

- DHCP, 

- PPPoE/Russia PPPoE, 

- PPTP/Russia PPTP, 

- L2TP/Russia L2TP

Wireless

- Basic Settings          

- Multiple SSID1          

- Multiple SSID2 

- Multiple SSID3         

- Multiple SSID4         

- Advanced Settings   

- Access Control        

- WDS Settings           

- WPS Settings           

- Wireless Schedule   

- Band Steering

QoS

- Up/Down speed control on WAN, 

- Bandwidth control based on IP address

Firewall


- MAC Filtering             

- IP/Port Filtering          

- Virtual Server(Port Forwarding) 

- URL Filtering              

- DMZ 

USB functional


- DLNA                         

- Samba                      

- FTP     

System

- Upgrade Firmware     

- Save/Reload Settings  

- Time Zone Settings           

- DDNS                         

- Denial-of-Service         

- TR-069 Config 

- Password Settings      

- Reboot Schedule         

- System Log 

- Statistics                     

- Run Command             

- Logout

 

Others

Package Contents

- A3002RU_V2 Wireless Router *1

- Power Adapter *1

- Ethernet Cable *1

- Quick Installation Guide *1

Environment - Operating Temperature: 0℃~50 ℃ (32 ℉~122℉)

- Storage Temperature: -40℃~70 ℃ (-40 ℉~158℉)

- Operating Humidity: 10%~90% non-condensing

- Storage Humidity: 5%~90% non-condensing

No

Title

Views
1

A3002RU Samba server instal

12

How to access A3002RU USB shared U disk video, pictures?


     It is suitable for: A3002RU

Application introduction:

A3002RU support file sharing function, the mobile storage devices (such as U disk, mobile hard disk, etc.) connected to the router's USB interface, LAN terminal equipment can access the resources of mobile storage devices, easy file sharing.

Diagram 

1.png

 Set up steps 

STEP-1:

Stores the resource you want to share with others into the USB flash disk or hard drive before you plug it into the USB port of the router.


STEP-2:

2-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


2-2. User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.


2.png

STEP-3:

Enable the SAMBA Server. Set the SAMBA Server account password .

4.png

STEP-4: Access the Samba server from the client.

4-1. Open This PC and type \\192.168.0.1 in the input box. And press the Enter key.

5.png


4-2. Enter the User name and password that you have set before, and then click OK.   

6.png

4-3. On this page, you will see the attached hard disk information. Click on this hard drive.

7.png

4-4. you can and good friends to share the resources inside the hard disk.

Notes:

If the Samba server can’t take effect immediately, please wait a few minutes. Or restart the service by clicking stop/start button.

2

A3002RU IPV6 function settings

8


     It is suitable for: A3002RU


Application:This article will introduce the configuration of IPV6 function and will guide you to configure this function correctly.In this article, we will take A3002RU as an example.

Note:

Please make sure that you are provided IPv6 internet service by your internet provider. If not, please contact with your IPv6 internet provider first.


STEP-1:

Make sure you have set up an IPv4 connection either manually or by using the Easy Setup wizard before setting up an IPv6 connection.


STEP-2:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


STEP-3:

Please go to Network ->WAN setting. Select WAN Type and configure the IPv6 parameters(here is PPPOE as an example). Click Apply.

2.png

STEP-4:

Switch to the IPV6 configuration page. The first step is to configure the IPV6 WAN setting(here is PPPOE as an example). Please note the red label.

3.png

STEP-5:

Configure RADVD for IPV6. Please keep consistent with the configuration of the picture. IPV6 only needs to be configured with "IPV6 WAN setting" and "RADVD for IPV6".

4.png

Finally in the status bar page to see if you get the IPV6 address.

3

How to use and set up IPTV

20

    Application introduction    

IPTV is an interactive network television, is a collection of Internet, multimedia, communications and other technology at an organic whole, through the Internet broadband lines to provide a wide range of interactive services, including digital television, the new technology.Users can watch the rich IPTV program at home via a network set-top box and a regular TV.

    This document applies to:N100RE, N150RT, N200RE, N210RE, N300RT, N302R Plus, A3002RU   

Part A: Introduce of IPTV setting page.

We can see the configuration webpage of the IPTV as below.

1.png

This article will guide you to configure the IPTV mode and LAN ports.


Part B: How to configure IPTV function correctly

Before IPTV is enabled, check with your ISP to confirm whether the current line supports VLAN TAG.

STEP-1:

If your current line supports VLAN TAG.You need to check Internet Tag and IPTV Tag,then you need to type in the VID fo different services (VID is provided by ISP).If you want to set some ports for IPTV (eg:port1), you should follow the steps below to configure.

①Choose IPTV Setting.→②Choose Triple Play/IPTV to open IPTV.→③Check Internet Tag and IPTV Tag.→④Enter type in the VID for different services.→⑤Check the LNA1 configuration.→⑥click “Save” to complete the configuration.

2.png


For example, if my ISP has told me that they use VLAN 40 for Internet service and VLAN 50 for IPTV service, I type in the parameters as above.

STEP-2:

If your current line does not support VLAN TAG.Please uncheck Internet Tag and IPTV Tag, and then leave the default Settings for the IPTV page.If you want to set some ports for IPTV (eg:port1), you should follow the steps below to configure.

①Choose IPTV Setting.→②Choose Triple Play/IPTV to open IPTV.→③Check the LNA1 configuration.→④click “Save” to complete the configuration.

3.png


Note: when you are not aware of your VLAN TAG, it is recommended that you configure it according to the STEP-2 method.

STEP-3:

Finally, connect the set-top box to LAN1 to watch IPTV, which requires a computer on the Internet, a mobile phone directly connected to a router or a wireless connection set up wirelessly.

4

A3002RU FTP server instal

291


     It is suitable for: A3002RU


Application:File server can be build quickly and easily via the USB port applications so that file upload and download can be more flexible. This guide introduces how to configure FTP service via the router. 


STEP-1:

Stores the resource you want to share with others into the USB flash disk or hard drive before you plug it into the USB port of the router.


STEP-2:

2-1.Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


2-2. User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

2.png


STEP-3:

Set the FTP server account password 

3.png


STEP-4: Access the FTP server by local network

4-1. Please open the web browser and type in address ftp://LAN IP, press enter. Here the IP address of the router is 192.168.0.1.

4.png


4-2. Enter the User name and password that you have set before, and then click Log On. 

5.png


4-3. You can visit the data in the USB device now.

6.png


STEP-5: Access the FTP server by external network.

5-1. You can also access the FTP server by external network. Please type in address ftp://wan IP to access to it. Here the WAN IP of the router is 10.8.0.19.

7.png


5-2. Enter the User name and password that you have set before, and then click Log On.  

8.png


5-3. You can visit the data in the USB device now.

9.png

Notes:

If the FTP server can’t take effect immediately, please wait a few minutes.

Or restart the service by clicking stop/start button.

5

A3002RU WDS Settings

163

    Application introduction    

    Settings Solution about how to configure WDS to TOTOLINK products. Take the A3002RU as the example of setting 2.4G wireless.

   This document applies to:  A702R, A850, A3002RU     


    Diagram    

1.png

    Preparation    

    ●Before configuration, make sure that both A Router and B Router are powered on.

    ●Connect your computer to the same network of router A and B.

    ●move the B router closer to the A router to find the B routing signals better for fast WDS.

    ●A Router and Router should be set to the same channel.

    ●Set both Router A and B should to the same band 2.4G or 5G.

    ●Choose the same models for A-router and B-router. If not, WDS function may not be implemented.


    Set up steps    


STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

2.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

3.png


STEP-3: A-router setting

3-1. Firstly connect the Internet for A-router then please go to Wireless 2.4GHz->WDS Settings page, and check which you have selected.(The type of A-router and B-router should be same )

Select Enable, then Input MAC Address of B-router in A-router and Select Auto for Data Rate, then Click Apply.

4.png

3-2. Please go to Wireless 2.4GHz->Advanced Settings page, select Channel Number which you must choice equal for the B-router.

5.png


STEP-4: B-router setting

4-1. Secondly use Bridge Mode for B-router then please go to Wireless 2.4GHz->WDS Settings page, and check which you have selected.

Select Enable, then Input MAC Address of A-router in B-router and Select Auto for Data Rate, then Click Apply.

6.png

4-2. Please go to Wireless 2.4GHz->Advanced Settings page, select Channel Number which you must choice equal for the A-router.

7.png

6

A3002RU repeater setting

153

    Application introduction    

      Solution about how to set repeater mode on TOTOLINK products.

   This document applies to:  A702R, A850, A3002RU     


    Settings    

STEP-1: 

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


STEP-2: 

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

2.png

STEP-3:

    Please go to Operation Mode ->Repteater Mode->wlan 2.4GHz or wlan 5GHz

then Click Apply.

3.png

STEP-4:

Firstly select Scan , then select host routers SSID and input Password of the host routers SSID, then select Change SSID and Possword to input SSID and Possword you want to fill in,then Click Next.

4.png


STEP-5:

Then you can change Repeater SSID in 5GHz. As below steps input SSID and Possword you want to fill in to 5GHz,then Click Connect.

5.png


PS: After completing the above operation, please re-connect your SSID after 1 minute or so.if the Internet is available it means that the settings are successful. Otherwise, please re-set the settings again

7

A3002RU Wireless SSID password setting

99

    Application introduction    

    The Wireless SSID and password are the basic information for you to connect Wi-Fi network. But sometimes you may forget or want to change them regularly, so here we will guide you how to check or modify the wireless SSID and password.

   This document applies to:  A702R, A850, A3002RU     


    Settings    

STEP-1: Enter the setup interface

Open a browser, enter 192.168.0.1. Input User Name and password (default admin/admin) on login management interface, as follows:

Note: The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

1.png


STEP-2: View or modify the wireless parameters

2-1. Check or modify in Easy Setup page.

Login management interface, first enter the Easy Setup interface, you can see 5G and 2.4G wireless settings, as follows:

2.png


2-2. Check and modify In the Advanced Setup

If you also need to set more parameters for WiFi, you can enter the Advanced Setup interface to set up.

3.png



Set the SSID and password according to the following procedure.

4.png


You are also able to set the Channel Width, Date Rate, RF Output Power.

5.png


    Questions and Answers    

Q1: Should I restart the router after setup wireless information?

A: After setting, you need to wait a few seconds for the wireless information to take effect.

8

A3002RU Upgrade the software settings

137


     It is suitable for: N100RE, N150RH, N150RT, N151RT, N200RE, N210RE, N300RT, N301RT , N300RH, N302R Plus, A702R, A850, A3002RU


Application:Solution about how to upgrade Firewall on the TOTOLINK products.


STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

2.png


STEP-3: Upgrade the software setting

Please go to System ->Upgrade Firmware page, and check which you have selected.

Select Local Upgrade files, then Click Upgrade 

    Then select Save/Reload Settings and click reset .

3.png

Note:DO Reset the router to factory default settings by RST or RST/WPS button after firmware upgrading fineshed.


STEP-4: System reset

Please go to System->Save/Reload Settiings page, and check which you have selected.Then Click Reset

4.png


Or please find the RST bottom in the box and use needle to press down the bottom more than five seconds.

5.png

9

A3002RU Reset settings

1508


     It is suitable for:N100RE, N150RH, N150RT, N151RT, N200RE, N210RE, N300RT, N301RT , N300RH, N302R Plus, A702R, A850, A3002RU


Application:Solution about how to reset TOTOLINK products to factory defaults.


STEP-1:

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

2.png


STEP-3: Login page reset

Please go to System->Save/Reload Settiings page, and check which you have selected.

then Click Reset.

3.png


STEP-4: RST Button reset

Please make sure your router’s power is on regularly, then press the

RST button for about 5~8s.

Loosen the button until your router’s LED lights all flashing, then you

have reset your router to default settings.

4.png

10

A3002RU PPPoE DHCP static IP settings

217


     It is suitable for: N100RE, N150RH, N150RT, N151RT, N200RE, N210RE, N300RT, N301RT , N300RH, N302R Plus, A702R, A850, A3002RU


Application:Solution about how to configure Internet mode with PPPoE ,Static IP and DHCP for TOTOLINK products


STEP-1:

    Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

1.png

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.


STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

2.png


STEP-3.1.1: Easy Setup DHCP setting

The Easy Setup page will turn up for basic and quick settingSelect DHCP Client  as WAN Connection Type, then Click Apply.

3.png

STEP-3.1.2: Advanced Setup DHCP setting

Please go to Network ->WAN Setting page, and check which you have selected.

Select DHCP Client as WAN Type, then Click Apply.

4.png


STEP-3.2.1: Easy Setup PPPOE setting

The Easy Setup page will turn up for basic and quick setting ,Select PPPoE as WAN Type and input your PPPoE username and password which are provided by your ISP. Then Click Apply

5.png



STEP-3.2.2: Advanced Setup PPPOE setting

Please go to Network ->WAN Setting page, and check which you have selected.

Select PPPoE as WAN Type and input your PPPoE username and password which are provided by your ISP. Then Click Apply

6.png

STEP-3.3.1: Easy Setup Static IP setting

The Easy Setup page will turn up for basic and quick setting,Selecting Static IP as WAN Connection Type and input your information about Static IP which you want to fill in .Then Click Apply

7.png


STEP-3.3.2: Advanced Setup Static IP setting

Please go to Network ->WAN Setting page, and check which you have selected.

Select Static IP as WAN Type and input your information about Static IP which you want to fill in .Then Click Apply

8.png