/themes/my_demo/public/assets/images/s24w1.png

U1003

U1003 is a 3-Port USB 3.0 Hub with RJ45 Gigabit Ethernet Adapter which allows users to connect to a wired network by plugging it into the computer’s available USB. It can deliver high transmission rate that is ideal for speeding up data transfers between network servers and other computers, such as video conferencing. 

- RJ45 Gigabit Ethernet Port

- Multi-Functional Extension Hub

- 3-Port USB 3.0 Provides Data Transfer Speeds up to 5Gbps

- Plug & Play with Increased Compatibility

- Lightweight & Super Portable

- Compatible with Windows XP/Vista/7/8/8.1/10, Mac OS 10.6~10.13 and Linux 4.XX

*Manual driver installation is required for Mac OS 10.6~10.13 and Linux 4.XX

General

Chipset

- RTL8153

Standards

- IEEE 802.3/802.3u, 802.3ab

Port

- RJ45 Giga LAN Port 

- 10/100/1000Mbps

- USB-A 3.0 Port x 3

Extended USB Cable

- 20 cm (excluding cable gland)

LED Indicator

- Blue LED Link/Act x1

Dimensions (L x W x H)

- 64 x 30 x 17.5mm

Others
Package Contents

- U1003 Network Adapter *1

- Quick Installation Guide *1

System Requirement

- Windows XP/Vista/7/8/8.1/10

- Mac OS 10.6~10.13

- Linux 4.XX

Environment

- Operating Temperature: 0℃~50 ℃ (32 ℉~122℉)

- Storage Temperature: -40℃~70 ℃ (-40 ℉~158℉)

- Operating Humidity: 10%~90% non-condensing

- Storage Humidity: 5%~90% non-condensing

  • 1

No

Title

Views
1

How to log in CP900's setting interface

11

    Application introduction    

If you want to login to CP900’s setting interface to configure some settings, please follow the steps below.

    It is suitable for:  CP900_V1    


STEP-1:

1-1. Connect your computer to the router by cable or wireless


1-2. Setup you PC to get the IP automatically (Here I take system W10 for example)


1-3. Click on 1.png at the bottom right corner on the screen

2.png

1-4. Click [Properties] button in the lower left corner

3.png

1-5. Double click on “Internet Protocol (TCP/IP)”.

4.png


STEP-2:

Now you have two ways to configure the TCP/IP protocol below

2-1. Use the first default IP address 192.168.0.254:

Assigned manually IP address 192.168.0.x “x” range from 2 to 253, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.254.

5.png

Enter 192.168.0.254 into the address bar of your browser. Log in the settings interface.

图片1.png


[Note]: 

192.168.0.254 can only be used in AP mode and WISP mode; Client mode and Repeater mode please use his second IP address 169.254.0.254.

 

2-2. Use the second IP address 169.254.0.254:

Assigned manually IP address 169.254.0.x “x” range from 2 to 253, the Subnet Mask is 255.255.255.0 and Gateway is 169.254.0.254.

7.png


Enter 169.254.0.254 into the address bar of your browser. Log in the settings interface.

8.png



[Note]: 

169.254.0.254 supports login in Client mode, Repeater mode, AP mode and WISP mode.

 

STEP-3:

After the setup is successful, your computer must choose to obtain an IP address automatically to access the network. As the picture shows.

9.png

2

How to Select Operation Mode of CPE Products

6

    Application introduction    

This document describes the characteristics and application scenarios of different modes supported by TOTOLINK CPE, including Client mode, Repeater mode, AP mode and WISP mode.

    It is suitable for:  CP900_V1    

STEP-1: Client mode

Client mode is used to transfer wireless connection into wired connection. In Client mode, the device serves as a wireless adapter. It receives the wireless signal from root AP or station, and provides wired network for users.

Scenario 1:

1.png

Scenario 2:

2.png

STEP-2: Repeater mode

Repeater Mode In this mode,you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.

Scenario 1:

3.png

Scenario 2:

4.png

STEP-3: AP mode

AP mode connect the superior AP/Router by wire, you can transfer the superior's AP/Router wired signal into wireless signal.

 

Scenario 1:

5.png

Scenario 2:

6.png

Scenario 3:

7.png

Scenario 4:

8.png


STEP-4: WISP Mode

WISP Mode In this mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN.

Scenario 1:

9.png



    FAQ Common problem    

Q1: How to reset the CPE to factory default Settings?

Keep the CPE powered on, press the RESET button on CPE or Passive PoE box about 8 seconds, the CPE will restore to factory default settings.

10.png


Q2: What Can I do If I forgot the CPE’s Web Login User Name and Password?

In case you changed your CPE’s Login User Name and Password, we suggest you reset your CPE to factory default settings by above operations. Then use the following parameters to login the CPE’s Web interface:

Default IP address: 192.168.0.254

User Name: admin

Password: admin