/themes/my_demo/public/assets/images/s24w1.png

EX210

EX210 is a wireless range extender, which works together with your existing router to expand the wireless coverage. Equipped with signal indicators and high-gain antennas, EX210 would bring the users with more convenience and better Wi-Fi experience.


300Mbps Wireless Speed 

EX210 delivers wireless speed up to 300Mbps on 2.4GHz. With high performance antennas, it greatly improves the reception sensitivity and helps to transfer the wireless signal to further distance with 300Mbps speed.


Extend your Wi-Fi to Every Corner

EX210 can extend your wireless network to every corner of your house. As a wireless N extender, , it helps to extend your source Wi-Fi signal to the largest extend, ensuring your Phones and PCs a reliable connection to the Internet.


One click on WPS for Easy Extension

Simply pressing the WPS button on both EX210 and your source router, secured home Wi-Fi network can be established quickly to extend the wireless coverage of your existing WLAN network.


Smart Phone UI for Setup

EX210 provides a smart UI on Phone web page, which enables users to configure the extender with only several steps. Wi-Fi extension has never been so easier on your Phone. 


Indicators to Show the Signal Status 

Green color indicates the signal is good. Orange or Red color indicates the signal is weak, please close the distance until it turns green to enjoy better Wi-Fi. If no color, it indicates the extension failed.


- Complies with 802.11b/g/n standards.

- Up to 300Mbps date rate for Wi-Fi network.

- Faster startup time, portable and compact design on structure.

- Supports quick setup on Phone UI page.

- Supports WPS (Wi-Fi Protected Setup) Wi-Fi extension by one-click. 

- Indicators to show the signal status timely. 

- Two internal antennas enhance the reception and transmission stability.

Hardware

Power Supply - AC 100V~240V
Antenna

- 2 * 4dBi Internal Antennas

Button

- 1 * WPS Button, 

- 1 * RST Button

LED Indicators

- 1 * SYS, 

- 1 * Wi-Fi

Dimensions (L x W x H) - 2.0 x 3.4 x 1.2 in. (52 x 85.7 x 30.9mm)

Wireless

Standards

- IEEE 802.11b

- IEEE 802.11g

- IEEE 802.11n

RF Frequency

- 2.4GHz/5GHz
Data Rate

- Up to 300Mbps

EVM

(Error Vector Magnitude)

- 11g: <-25dB; 

- 11n:<-28dB

Wireless Security

- 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK

RF Power Rate

 - 11b: 11M 18±1.5dBm;

 - 11g:  54M 16±1.5dBm;

 - 11n: MCS7 HT20 16±1.5dBm;MCS7 HT40 16±1.5dBm;

Others
Package Contents

- EX210 Wireless Extender * 1

- Quick Installation Guide * 1

Environment

- Operating Temperature: 0℃~50℃ (32 ℉~122℉)

- Storage Temperature: -40℃~70 ℃ (-40 ℉~158℉)

- Operating Humidity: 10%~90% non-condensing

- Storage Humidity: 5%~90% non-condensing

No

Title

Views
1

How to Configure the AP Mode on the EX1200M

7

    Application introduction    

To set up a Wi-Fi network from an existing wired (Ethernet) network so that multiple devices can share the Internet. Here takes EX1200M as demonstration.

   It is suitable for: EX1200M    


    Set up steps    

STEP-1Configure the extension

Please reset the extender first by pressing the reset button/hole on the extender.

Connect your computer to the extender wireless network.

Note:

1. The default Wi-Fi Name and Password are printed on the Wi-Fi Info Card to connect to theextender.

2. Do not connect the extender to the wired network until the AP mode is set.

STEP-2Login to the management page

Open the browser, clear the address bar, enter 192.168.0.254 to the management page, click Setup Tool.

1.png


STEP-3AP mode setting

AP mode supports both 2.4G and 5G. The following describes how to set up 2.4G first, then set 5G:

3-1. 2.4GHz Extender Setup

ClickBasic Setup->2.4GHz Extender Setup->Select AP mode, setting the SSID, setting password, If you need to see the password,check Show, Finally click Apply.

2.png

After the setup is successful, the wireless will be interrupted and you need to reconnect to the Extender's wireless SSID.

3-2. 5GHz Extender Setup

Click Basic Setup->5GHz Extender Setup->Select AP mode, setting the SSID, setting password, If you need to see the password, check Show, Finally click Apply.

3.png

STEP-4

Connect the extender to the wired network through the network cable as shown below.

4.png

STEP-5

Congratulations! Now all your Wi-Fi enabled devices can connect to the customized wireless network.

2

How to change SSID of extender

689

    Application introduction    

The wireless extender is a repeater (Wi-Fi signal amplifier), which relays a WiFi signal, expands the original wireless signal, and extends the WiFi signal to other places where there is no wireless coverage or where the signal is weak.


    This Article Applies to: EX1200M    

    Diagram    

1.png


    Set up steps    

STEP-1Configure the extension

●  First, make sure the extender has successfully extended the main router.If no Settings have been set, click the reference instruction manual.

●  Connect to the extender's LAN port with a network cable from a computer network port (or to search for and connect the expander's wireless signal)

Note: The name of the wireless password after successful expansion is either the same as the upper level signal, or it is a custom modification of the extension process.

STEP-2Assigned manually IP address

Extender LAN IP address is 192.168.0.254, please type in IP address 192.168.0.x (“x” range from 2 to 254), the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.254.

2.png

Note: How to manually assign an IP address, please click the FAQ# (How to manually set an IP address)




STEP-3Login to the management page

Open the browser,clear the address bar,enter 192.168.0.254 to the management page,click Setup Tool.

3.png


STEP-4View or modify the wireless parameters

4-1. View the 2.4G wireless SSID and password

Click Advanced Setup->wireless(2.4GHz)->Extender Setup, Select the SSID configuration type, Modify the SSID, If you need to see the password, check Show, Finally click Apply.

Note: The password cannot be modified. It is the password for connecting to the upper router.

4.png


4-2. View the 5G wireless SSID and password

Click Advanced Setup->wireless(5GHz)->Extender Setup, Select the SSID configuration type, Modify the SSID, If you need to see the password, check Show, Finally click Apply.

Note: The password cannot be modified. It is the password for connecting to the upper router.

5.png


STEP-5Assigned by DHCP Sever 

After you have successfully changed the expander's SSID, Please select Obtain an IP address automatically and Obtain DNS Server address automatically.

6.png

Note: After the extender is successfully set up, Your terminal device must choose to obtain an IP address automatically to access the network.


STEP-6Extender position display

Move the Extender to a different location for a best Wi-Fi access.

7.png

3

Can the extender make a WPS connection with other brands?

142


     It is suitable for: EX100, EX200, EX300, EX750, EX1200M, EX1200T

Of course,TOTOLINK Extender can connect with many other brands WPS-supported routers by WPS button such as TP-LINK, D-LINK and TRENDNET.