Application introduction:

This articles Applies to wireless router that’s compatible with TOTOLINK App. This article will take A720R as an example.

 Set up steps 

STEP-1: Follow the steps below to connect your router.

STEP-2: Connect your smart phone to TOTOLINK Wi-Fi. The default wireless network name of TOTOLINK wireless router are printed on the bottom label.

STEP-3: Launch the Tether App on your phone.

STEP-4: Select your TOTOLINK wireless router from device list.Then Enter admin for the password and then click LOGIN.

STEP-5: Log in to Quick Setup.(Auto jump Quick Setup is only Applicable for the first connection setup)

STEP-6: Quick Setup.

STEP-7: More features: Click Application or Tools.

 STEP-8: Binding router, remote management. 

Application introduction 

This article describes how to quickly make a wireless connection through the router's WPS button.

Diagram

Set up steps 

STEP-1:

l Please make sure your router has WPS button before setting.

l Please make sure your wireless client supports WPS functionality before setting.

STEP-2:

Press WPS button on the router for 1s, WPS enabled. There are two types of wireless router WPS buttons: RST/WPS button and WPS button. As shown below.

2-1. RST/WPS button：

2-2. WPS button：

Note: If router is a RST/WPS button, no more than 5s, router will be reset to factory defaults if you press it for more than 5s.

STEP-3:

After pressing the WPS button, use wireless client to connect to the router WIFI signal. Using Computer and Mobile phone wireless connection as an example. As shown below.

3-1. Computer wireless connection:

3-2. Mobile phone  wireless connection:

Application introduction 

Repeater mode expands the upper-level wireless signal by wireless to extend the wireless signal to a farther distance. Here is an example of A1004.

Diagram

Set up steps 

STEP-1：Assigned manually IP address

A1004 LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-2：Login to the management page

Open the browser,clear the address bar,enter 192.168.0.1 to the management page，click Advance setup.

The repeater mode supports both 2.4G and 5G. Here's how to set up 2.4G first, then set 5G.

STEP-3：2.4G repeater settings

3-1.  2.4GHz wireless setting

❶ Click Wireless Setup -> ❷Select 2.4GH Basic network -> ❸ Set Wireless SSID -> ❹ Set Wireless Password -> ❺ Click Apply.

3-2.  2.4GHz extension setting

❶ Click Wireless Multibridge -> ❷ Select 2.4GHz -> ❸ Select Repeater -> ❹ Click AP Scan -> ❺ Select the wireless you need to expand -> ❻ Enter the upper-level wireless password, and finally ❼ click Apply.

STEP-4：5G repeater settings

4-1.  5GHz wireless setting

❶ Click Wireless Setup -> ❷ Select 5GH Basic network -> ❸ Set Wireless SSID -> ❹ Set Wireless Password -> ❺ Click Apply.

4-2.  5GHz extension setting

❶ Click Wireless Multibridge -> ❷ Select 5GHz -> ❸ Select Repeater -> ❹ Click AP Scan -> ❺ Select the wireless you need to expand -> ❻Enter the upper-level wireless password, and finally ❼ click Apply.

STEP-5：After the setting is successful, please obtain the IP setting automatically, and the computer can connect to the network.

STEP-6：Now all Wi-Fi enabled devices can connect to a custom wireless network.

 FAQ Common problem 

Q1: After the bridge mode is set successfully, you will not be able to access the router. If you need to revisit, there are two ways!

1. Press the reset button/hole on the router to restore the router to factory settings;

2. Log in to the router management page by setting a fixed IP (refer to STEP-1).

Set up steps 

STEP-1: Connect your computer

Connect to the router's LAN port with a network cable from a computer network port (or to search for and connect the  router's wireless signal).

STEP-2: Assigned manually IP Address

2-1. If the router’s LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1.

2-2. If the router’s LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-3: Login to the TOTOLINK router in your browser. Take 192.168.0.1 as an example.

STEP-4: After setting up the router successfully, please select Obtain an IP address automatically and Obtain DNS Server address automatically.

Note: Your terminal device must choose to obtain an IP address automatically to access the network.

Application introduction 

This article will introduce the difference between Router Mode, Repeater mode, AP mode, and WISP Mode.

 Set up steps 

STEP-1: Router Mode(Gateway mode)

Router Mode, the device is supposed to connect to the internet via ADSL/Cable modem. The WAN type can be setup on WAN page, including PPPOE, DHCP client, Static IP.

STEP-2: Repeater mode

Repeater Mode, you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.

STEP-3: AP mode(Bridge mode)

AP mode, the router acts as a wireless switch, you can transfer the superior's AP/Router wired signal into wireless signal.

STEP-4: WISP Mode

WISP Mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN.

 FAQ Common problem 

Q1: Can I log in to the TOTOLINK ID after setting the AP mode/Repeater mode?

A: TOTOLINK ID cannot be logged in after setting AP mode/Repeater mode.

Q2: How to enter the router management interface in AP mode/Repeater mode?

A: Refer to FAQ#How to login to router by manually configuring IP

Application introduction 

After entering the management address of the router in the address bar of Chrome browser, the page cannot be displayed after entering the management password, as shown below.

Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password. 

Method One: login via PC 

STEP-1: Change browser and clear browser cache

Try changing old version (before 72.0.3626.96) of Chrome browser or try other browser, such as Firefox, Internet Explorer, etc., and clear your browser cache. 

Delete cookies on the web browser. Here we take Firefox for example.

Note: In general, the browser enters the management address of the router and error pops up. Please use this method first.

STEP-2: Enter 192.168.0.1 into the address bar of your browser. Log in the settings interface.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

 Method Two: login via tablet/Cellphone 

STEP-1: Change browser and clear browser cache

Try other browser, such as Firefox, Opera, etc., and clear your browser cache.

STEP-2: Enter 192.168.0.1 into the address bar of your browser. Log in the settings interface.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

Application introduction 

The system log of the router can be used to find out why the network connection fails.

Set up steps 

STEP-1:

Open the browser, clear the address bar, enter 192.168.0.1, select Advance Setup.fill in the administrator account and password (default admin), click Login, as follows:

STEP-2:

Make sure your router is connected to the internet.

STEP-3:

In the left menu, click System -> System Log.

STEP-4:

Administrator email settings.

①Fill in the recipient email, for example: fae@zioncom.net

②Fill in the recipient server, for example: smtp.zioncom.net

③Fill in the sender's email.

④Fill in the sender's email and password.

⑤Click "Apply".

STEP-5:

Click Send E-mail lmmediately, click OK.

Note:

Before sending an email, you need to make sure the router is connected to the internet.

 Application introduction 

The system log of the router can be used to find out why the network connection fails.

Take A1004 as an example:

Set up steps 

STEP-1:

Login to the TOTOLINK router in your browser.

STEP-2:

Confirm that your router is connected to internet.

STEP-3:

In the left menu, click System ->System Log.

STEP-4: Admin E-mail Setup.

①Enter Recipient E-mail, E.g: fae@zioncom.net

②Enter Recipient Server,E.g: smtp.zioncom.net

③Enter E-mail of sender

④Enter E-mail and Password of sender

⑤Click "Apply"

STEP-5: Send E-mail immediately.

Note:

Before sending the E-mail, you need to confirm that the router is connected to the internet.

 Preparation 

l Before downloading files. please confirm the hardware version ofyour device and choose the corresponiding firmware version to uparade. 

l Wrong firrmware version may damage your device and no warrante.

 Set up steps 

STEP-1: Guide for Hardware Version

For most TOTOLINK routers, you can see two bar coded stickers at the front of the device, the character string started with Model No.(for example N300RT) and ended with Hardware Version (for example V2.0) is the serial number of your device. See below:

STEP-2:

Open browser, enter www.totolink.net. Download the required files.

For example, if your hardware version is V2.0 , please download V2 version.

Note: If the hardware version is V1, V1 will be hidden.

STEP-3:

Unzip the file, correct upgrade file name is suffixed with ”web” or “bin” (except for some special models)

    It is suitable for:  All TOTOLINK Router  

    Method One：  

Check the label on the bottom of the router to get the login address of the router, as shown below.

   Method Two：  

Obtain the login address of the router through the computer (take win10 system as an example).

STEP-1: 

The computer connects to the wireless signal of the router. (The back sticker has the factory default wireless signal name)

STEP-2: 

2-1. Click on wireless icon at the bottom right corner on the screen, Select Network & Internet settings.

2-2. Select the connected wireless network.

2-3. Select Details to check whether an IP address is obtained.

If the IPV4 address is 192.168.0.*, the default gateway of IPV4 is 192.168.0.1, indicating that the login address of the router is 192.168.0.1.

If the IPV4 address is 192.168.1.*, the default gateway of IPV4 is 192.168.1.1, indicating that the login address of the router is 192.168.1.1.

If the IP is not available, you can disconnect the signal and reconnect it. If it is still invalid, you can restore the router to the factory and check the IP address obtained after the connection signal.

Note: Before this, please confirm that your computer is selected to "acquire IP address automatically".

For the setting method of the computer automatically obtaining the IP address, refer to the following figure (take win10 system as an example).

Obtain the login address of the router through your mobile phone.

STEP-1: The wireless signal that the phone connects to the router. (The back sticker has the factory default wireless signal name)

STEP-2: Select your phone's wireless network settings to check if you have an IP address.

At this point, the IPV4 address is 192.168.0.*, and the IPV4 default gateway is 192.168.0.1, indicating that the router's login address is 192.168.0.1.

STEP-3: Enter 192.168.0.1 in the address bar of the mobile browser.

STEP-4: If you still can't enter, you can change the browser or a mobile phone or computer through the 192.168.0.1 login interface.

STEP-5: If the fourth step is invalid, the router can be reset.

Reset method:

1. Please make sure your router’s power is on regularly, then press the

RST button for about 10s.(The RESET pin should be held with a pointed object such as a paper clip or a pen tip)

2. Loosen the button until your router’s LED lights all flashing, then you

have reset your router to default settings.