Application introduction:

This articles Applies to wireless router that’s compatible with TOTOLINK App. This article will take A720R as an example.

 Set up steps 

STEP-1: Follow the steps below to connect your router.

STEP-2: Connect your smart phone to TOTOLINK Wi-Fi. The default wireless network name of TOTOLINK wireless router are printed on the bottom label.

STEP-3: Launch the Tether App on your phone.

STEP-4: Select your TOTOLINK wireless router from device list.Then Enter admin for the password and then click LOGIN.

STEP-5: Log in to Quick Setup.(Auto jump Quick Setup is only Applicable for the first connection setup)

STEP-6: Quick Setup.

STEP-7: More features: Click Application or Tools.

 STEP-8: Binding router, remote management. 

Package Contents

• 1 T10 Master

• 2 T10 Satellites

• 3 Power Adapters

• 3 Ethernet Cables

Steps

1. Remove the power cord from your modem. Wait 2 minutes.

2. Insert an ethernet cable into your modem.

3. Connect ethernet cable from modem into the yellow WAN port of the T10 labeled Master.

4. Power on your modem and wait until it is fully booted.

5. Power on the Master and wait until status LED is blinking green.

6. Connect to the Master’s SSID labeled TOTOLINK_XXXXXX or TOTOLINK_XXXXXX_5G.

7. Once successfully connected to the Master and able to access the Internet, please change the SSID and password to that of your choosing for security reasons. Then you can position the 2 sateIIites throughout your home.

Note: The color of the sateIIite’s status LED acts as a signal strength indicator.

Green/Orange = Excellent or OK signal

Red = Poor signal, needs to be moved closer to the Master

FAQs

How to set my own SSID and Password?

1. Connect to the Master using a wired or wireless connection.

2. Open a web browser and enter http://192.168.0.1 into the address bar.

3. Enter User Name and Password and click Login. Both are admin by default in lowercase letters.

4. Enter your new SSID and Password within the Easy Setup Page for both 2.4Ghz and 5Ghz bands. Then click AppIy.

Note: The default access address is located on the bottom of each unit. However, this may vary de- pending on your network configuration. In most cases, if this address does not work you may try the alternate address 192.168.1.1. Also, check your Wi-Fi settings to make sure you are connected to the router you are trying to configure.

For questions or additionaI assistance in setting up your T10 WhoIe Home Wi-Fi Mesh System, pIease contact us at fae@zioncom.net

Set up steps 

STEP-1: Connect your computer

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Select advanced settings to enter the settings page

STEP-4:

Enter the  Static DHCP Setting to open the setting and checklist the Enable,input IP Address ,MAC Address and Comment.After click Apply ,we can see the information in the static DHCP List.

Package Contents

• 1 T10 Master

• 2 T10 Satellites

• 3 Power Adapters

• 3 Ethernet Cables

Steps

1. Remove the power cord from your modem. Wait 2 minutes.

2. Insert an ethernet cable into your modem.

3. Connect ethernet cable from modem into the yellow WAN port of the T10 labeled Master.

4. Power on your modem and wait until it is fully booted.

5. Power on the Master and wait until status LED is blinking green.

6. Connect to the Master’s SSID labeled TOTOLINK_T10 or TOTOLINK_T10_5G. Password is

abcdabcd for both bands.

7. Once successfully connected to the Master and able to access the Internet, please change the SSID and password to that of your choosing for security reasons. Then you can position the 2 sateIIites throughout your home.

Note: The color of the sateIIite’s status LED acts as a signal strength indicator.

Green/Orange = Excellent or OK signal

Red = Poor signal, needs to be moved closer to the Master

FAQs

How to set my own SSID and Password?

1. Connect to the Master using a wired or wireless connection.

2. Open a web browser and enter http://192.168.0.1 into the address bar.

3. Enter User Name and Password and click Login. Both are admin by default in lowercase letters.

4. Enter your new SSID and Password within the Easy Setup Page for both 2.4Ghz and 5Ghz bands. Then click AppIy.

Note: The default access address is located on the bottom of each unit. However, this may vary de- pending on your network configuration. In most cases, if this address does not work you may try the alternate address 192.168.1.1. Also, check your Wi-Fi settings to make sure you are connected to the router you are trying to configure.

For questions or additionaI assistance in setting up your T10 WhoIe Home Wi-Fi Mesh System, pIease contact us at fae@zioncom.net

 Set up steps 

STEP-1:Guide for Hardware Version

For most TOTOLINK routers, you can see two bar coded stickers underneath each device, the character string will begin with Model No.(T10) and end with the serial number for each device. See below:

STEP-2: Download Firmware

Open browser, enter www.totolink.net. Download the required files.

For example, if your hardware version is V2.0 , please download V2 version.

STEP-3: Unzip the file

The correct upgrade file name is suffixed with ”web”.

STEP-4: Upgrade Firmware

❶Click Management->upgrade firmware. ❷With configuration upgrade (if selected, the router will be restored to the factory configuration).❸Choose the firmware file you want to upload. Finally❹Click Upgrade button. Wait for a few minutes while the firmware is updating, and the router will restart automatically.

Notice:

1. DO NOT power off the device or close the browser window while uploading as it may crash the system.

2. When downloading the correct firmware update, you'll want to extract and upload the Web File

format type

Application introduction 

This article describes how to quickly make a wireless connection through the router's WPS button.

Diagram

Set up steps 

STEP-1:

l Please make sure your router has WPS button before setting.

l Please make sure your wireless client supports WPS functionality before setting.

STEP-2:

Press WPS button on the router for 1s, WPS enabled. There are two types of wireless router WPS buttons: RST/WPS button and WPS button. As shown below.

2-1. RST/WPS button：

2-2. WPS button：

Note: If router is a RST/WPS button, no more than 5s, router will be reset to factory defaults if you press it for more than 5s.

STEP-3:

After pressing the WPS button, use wireless client to connect to the router WIFI signal. Using Computer and Mobile phone wireless connection as an example. As shown below.

3-1. Computer wireless connection:

3-2. Mobile phone  wireless connection:

Set up steps 

STEP-1: Connect your computer

Connect to the router's LAN port with a network cable from a computer network port (or to search for and connect the  router's wireless signal).

STEP-2: Assigned manually IP Address

2-1. If the router’s LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1.

2-2. If the router’s LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-3: Login to the TOTOLINK router in your browser. Take 192.168.0.1 as an example.

STEP-4: After setting up the router successfully, please select Obtain an IP address automatically and Obtain DNS Server address automatically.

Note: Your terminal device must choose to obtain an IP address automatically to access the network.

Application introduction 

This article will introduce the difference between Router Mode, Repeater mode, AP mode, and WISP Mode.

 Set up steps 

STEP-1: Router Mode(Gateway mode)

Router Mode, the device is supposed to connect to the internet via ADSL/Cable modem. The WAN type can be setup on WAN page, including PPPOE, DHCP client, Static IP.

STEP-2: Repeater mode

Repeater Mode, you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.

STEP-3: AP mode(Bridge mode)

AP mode, the router acts as a wireless switch, you can transfer the superior's AP/Router wired signal into wireless signal.

STEP-4: WISP Mode

WISP Mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN.

 FAQ Common problem 

Q1: Can I log in to the TOTOLINK ID after setting the AP mode/Repeater mode?

A: TOTOLINK ID cannot be logged in after setting AP mode/Repeater mode.

Q2: How to enter the router management interface in AP mode/Repeater mode?

A: Refer to FAQ#How to login to router by manually configuring IP

Application introduction 

After entering the management address of the router in the address bar of Chrome browser, the page cannot be displayed after entering the management password, as shown below.

Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password. 

Method One: login via PC 

STEP-1: Change browser and clear browser cache

Try changing old version (before 72.0.3626.96) of Chrome browser or try other browser, such as Firefox, Internet Explorer, etc., and clear your browser cache. 

Delete cookies on the web browser. Here we take Firefox for example.

Note: In general, the browser enters the management address of the router and error pops up. Please use this method first.

STEP-2: Enter 192.168.0.1 into the address bar of your browser. Log in the settings interface.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

 Method Two: login via tablet/Cellphone 

STEP-1: Change browser and clear browser cache

Try other browser, such as Firefox, Opera, etc., and clear your browser cache.

STEP-2: Enter 192.168.0.1 into the address bar of your browser. Log in the settings interface.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

Application introduction 

You can maintain the system time by synchronizing with a public time server over the Internet.

Set up steps 

STEP-1:Login to the TOTOLINK router in your browser.

STEP-2: In the left menu, click Management->Time Setting, follow the steps below.

❶Time Zone select

❷click NTP Client Update

❸Enter NTP Server

❹click Apply

❺click Copy PC's  Time

[Note]:

Before time Setting, you need to confirm that the router is connected to the internet.