Application introduction:

This articles Applies to wireless router that’s compatible with TOTOLINK App. This article will take A720R as an example.

 Set up steps 

STEP-1: Follow the steps below to connect your router.

STEP-2: Connect your smart phone to TOTOLINK Wi-Fi. The default wireless network name of TOTOLINK wireless router are printed on the bottom label.

STEP-3: Launch the Tether App on your phone.

STEP-4: Select your TOTOLINK wireless router from device list.Then Enter admin for the password and then click LOGIN.

STEP-5: Log in to Quick Setup.(Auto jump Quick Setup is only Applicable for the first connection setup)

STEP-6: Quick Setup.

STEP-7: More features: Click Application or Tools.

 STEP-8: Binding router, remote management. 

Installation Diagram

 Interface 

 Method One: login via tablet/Cellphone 

STEP-1:

Find TOTOLINK_A702R or TOTOLINK_A702R_5G on the WLAN list of your Phone, and choose to connect. Then any Web browser on your Phone and enter http://itotolink.net on the address bar.

STEP-2:

Input admin for both User Name and Password on the coming page, then click Login.

STEP-3:

Click Quick Setup on the coming page.

STEP-4: 

Internet Setting. Choose a suitable WAN Connection type from the list, and fill in the information required.

STEP-5: 

Wireless Setting. Create passwords for 2.4G and 5G Wi-Fi (Here users could also revise the default Wi-Fi name) and then click Next.

STEP-6: 

It takes several seconds to save the settings and then your router will restart automatically. This time your Phone will be disconnected from the router. Please back to the WLAN list of your phone to choose the new Wi-Fi name and input the correct password. Now, you could enjoy the Wi-Fi.

 Method Two: login via PC 

STEP-1:

Connect your computer to the router by cable or wireless. Then run any Web browser and enter http://itotolink.net in the address bar.

STEP-2:

Set a new login password for the device, it is recommended to set the password with alphanumeric characters and then press Install.

STEP-3:

Enter admin for User name, then enter new password in step 2 or admin, type the verification code then press LOGIN.

STEP-4:

Click on "Auto Detect" to detect the Wan Type in your network.

STEP-5:

Now you can see the Easy Setup page. All basic settings could be done here, including Internet Settings and Wireless Settings.

Application introduction: This tutorial will show you how to configure TR069 feature on TOTOLINK Router devices.

Setup steps

STEP-1: Install router as the following diagram

The router WAN IP and TR069 server IP must be on the same network segment or can access each other; TR069 server needs to turn off the firewall and other functions.

STEP-2: Login router

Access Login page (Default IP: 192.168.0.1) and then you need enter the Administrator information (Default ID and Password is admin).

STEP-3: WAN settings

Go to the Advanced Setting page, setup the WAN information.

STEP-4: TR069 settings

Next, setup the TR069 information.

R069 – Connection Information

Set up steps 

STEP-1: Connect your computer

Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.0.1 into the address bar of your browser.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

STEP-2:

User Name and Password are required, by default both are admin in lowercase letter. Click LOGIN.

STEP-3:

Enter advanced settings to select the LAN settings in Network,click the Set Static DHCP.

STEP-4:

Checklist the Enable Static DHCP to open the setting,input IP Address ,MAC Address and Comment.After click Apply ,we can see the information in the static DHCP List.

Application introduction 

This article describes how to quickly make a wireless connection through the router's WPS button.

Diagram

Set up steps 

STEP-1:

l Please make sure your router has WPS button before setting.

l Please make sure your wireless client supports WPS functionality before setting.

STEP-2:

Press WPS button on the router for 1s, WPS enabled. There are two types of wireless router WPS buttons: RST/WPS button and WPS button. As shown below.

2-1. RST/WPS button：

2-2. WPS button：

Note: If router is a RST/WPS button, no more than 5s, router will be reset to factory defaults if you press it for more than 5s.

STEP-3:

After pressing the WPS button, use wireless client to connect to the router WIFI signal. Using Computer and Mobile phone wireless connection as an example. As shown below.

3-1. Computer wireless connection:

3-2. Mobile phone  wireless connection:

Set up steps 

STEP-1: Connect your computer

Connect to the router's LAN port with a network cable from a computer network port (or to search for and connect the  router's wireless signal).

STEP-2: Assigned manually IP Address

2-1. If the router’s LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1.

2-2. If the router’s LAN IP address is 192.168.0.1, please type in IP address 192.168.0.x （“x” range from 2 to 254）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.1.

STEP-3: Login to the TOTOLINK router in your browser. Take 192.168.0.1 as an example.

STEP-4: After setting up the router successfully, please select Obtain an IP address automatically and Obtain DNS Server address automatically.

Note: Your terminal device must choose to obtain an IP address automatically to access the network.

Application introduction 

This article will introduce the difference between Router Mode, Repeater mode, AP mode, and WISP Mode.

 Set up steps 

STEP-1: Router Mode(Gateway mode)

Router Mode, the device is supposed to connect to the internet via ADSL/Cable modem. The WAN type can be setup on WAN page, including PPPOE, DHCP client, Static IP.

STEP-2: Repeater mode

Repeater Mode, you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.

STEP-3: AP mode(Bridge mode)

AP mode, the router acts as a wireless switch, you can transfer the superior's AP/Router wired signal into wireless signal.

STEP-4: WISP Mode

WISP Mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN.

 FAQ Common problem 

Q1: Can I log in to the TOTOLINK ID after setting the AP mode/Repeater mode?

A: TOTOLINK ID cannot be logged in after setting AP mode/Repeater mode.

Q2: How to enter the router management interface in AP mode/Repeater mode?

A: Refer to FAQ#How to login to router by manually configuring IP

Application introduction 

After entering the management address of the router in the address bar of Chrome browser, the page cannot be displayed after entering the management password, as shown below.

Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password. 

Method One: login via PC 

STEP-1: Change browser and clear browser cache

Try changing old version (before 72.0.3626.96) of Chrome browser or try other browser, such as Firefox, Internet Explorer, etc., and clear your browser cache. 

Delete cookies on the web browser. Here we take Firefox for example.

Note: In general, the browser enters the management address of the router and error pops up. Please use this method first.

STEP-2: Enter 192.168.0.1 into the address bar of your browser. Log in the settings interface.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

 Method Two: login via tablet/Cellphone 

STEP-1: Change browser and clear browser cache

Try other browser, such as Firefox, Opera, etc., and clear your browser cache.

STEP-2: Enter 192.168.0.1 into the address bar of your browser. Log in the settings interface.

Note:The default access address varies depending on the actual situation. Please find it on the bottom label of the product.

 Application introduction 

By port forwarding, the data for Internet applications can pass through the firewall of the router or gateway. This article will show you how to forward ports on your router, take N100RE as an example.

Set up steps 

STEP-1:

In the left menu of the web interface, click Firewall ->Port Forwarding ->Enable.

STEP-2:

Choose the Rule Type from the drop-down list, and then fill in the blank as below, and then click Apply.

--IP Address: IP address of the server

--Internal Port: Actual port of the server

--External Portnternal Port: Port to access the server

--Remote IP Address: Suggested blank

--Comment: Set a name for rule (e.g. totolink)

 STEP-3:

Ensure that the port successfully added to the Current Port Forwarding List.

The router's port forwarding settings are complete

Here with FTP server as an example (WIN10), check that the port forwarding is successfully.

1. Open the Control Panel\All Control Panel Items\Administrative Tools\Add FTP Server

2. Input the ftp site name, Select the path; Click next

3. Select the target PC address，Sets the port, Click Next;

4. Define users and permissions, Click Finish.

5. Now, you can access FTP over a LAN, Login Address:ftp://192.168.0.242;

6. Check ROUTER WAN IP, in the public network use it to log into the FTP Server; 

E. g  ftp://113.90.122.205:21;

Normal visit, verify that the port forwarding OK

 Preparation 

l Before downloading files. please confirm the hardware version ofyour device and choose the corresponiding firmware version to uparade. 

l Wrong firrmware version may damage your device and no warrante.

 Set up steps 

STEP-1: Guide for Hardware Version

For most TOTOLINK routers, you can see two bar coded stickers at the front of the device, the character string started with Model No.(for example N300RT) and ended with Hardware Version (for example V2.0) is the serial number of your device. See below:

STEP-2:

Open browser, enter www.totolink.net. Download the required files.

For example, if your hardware version is V2.0 , please download V2 version.

Note: If the hardware version is V1, V1 will be hidden.

STEP-3:

Unzip the file, correct upgrade file name is suffixed with ”web” or “bin” (except for some special models)