- Complies with IEEE802.11n /g/b standards on 2.4G band.
- Supports DHCP/Static IP/ PPPoE(dual access)/PPTP(dual access) / L2TP(dual access) broadband functions.
- Supports Passive PoE power supply, transmitting distance can be far as 60 meters, more flexible for cabling deployment.
- Supports Qos bandwidth control.
- Supports 64/128-bit WEP, WPA, WPA2, WPA-Mixed security.
- Two Built-in dual polarized antennas.
- 4 intelligent LED indicators intuitively show signal strength.
- RF power up to 500mw.
- WDS function connection.
- IP65 level dust-proof and water-proof, 6KV lighting-proof and 15KV ESD static electricity-proof.
- Provides AP/Client/Repeater/WISP working modes.
| Hardware | |
|---|---|
| Interface | - 1 *100BaseTX (Auto MDI/MDIX) LAN Port (Passive PoE Supported) |
| Power Supply |
- 12VDC /1A (PoE) - Voltage range: 12-24VDC |
| Button | - 1 *RESET Button |
| Antenna | - 2 *Built-in 11dBi dual polarized antennas |
| LED Indicators |
- 1 *Power, - 1 *LAN, - 1 *WLAN, - 4 *Signal Strength |
| Dimensions（L X W X H） | - 262 x 87 x 50mm |
Wireless | |
| Wireless standard |
- IEEE 802.11n - IEEE 802.11g - IEEE 802.11b |
RF Frequency |
- 2.4~2.4835GHz |
| Data Rate | - Up to 300Mbps |
EIRP |
< 27dBm |
| Wireless Security | - 64/128-bit WEP, WPA, WPA2, WPA-Mixed |
| Reception Sensitivity |
- 11b 11M: -81 dBm@10% PER - 11g 54M: -68 dBm@10% PER - 11n HT20 MCS7: -65 dBm@10% PER HT40 MCS7: -62 dBm@10% PER |
Software | |
Operation Mode |
- AP Mode - Repeater Mode - Client Mode - WISP Mode |
| MIMO Type | - 2.4G 2Tx-2Rx |
Network |
- LAN Setting - WAN Setup (WISP Mode only) - VLAN Settings (WISP Mode only) |
| Wireless |
- Basic Setting, - Advanced Setting, - WDS Setting, - Access Control, - WPS Setting, - QoS |
| Firewall |
- IP/Port Filtering, - MAC Filtering, - URL Filtering, - Port Forwarding, - DMZ |
| Management |
- Upgrade Firmware, - Save/ Reload Setting, - Time Zone Setting, - Password Setting, - Reboot Schedule , - Reboot |
| Reliability |
- 6KV Lightning Protection - 15KV ESD Protection - IP65 level dustproof and waterproof |
| Others | |
| Package Contents |
- CP300 Wireless CPE *1 - Power Adapter *1 - User Guide *1 - Ethernet Cable *1 - Strips*2 |
| Environment |
- Operating Temperature: -40℃~70℃ (-40 ℉~158℉) - Storage Temperature: -40℃~70 ℃ (-40 ℉~158℉) - Operating Humidity: 5%~95% non-condensing - Storage Humidity: 5%~95% non-condensing |
It is suitable for: CP300 |
Application introduction:
This document describes the characteristics and application scenarios of different modes supported by TOTOLINK CPE, including Client mode, Repeater mode, AP mode and WISP mode.
Set up steps
STEP-1: Client mode
Client mode is used to transfer wireless connection into wired connection. In Client mode, the device serves as a wireless adapter. It receives the wireless signal from root AP or station, and provides wired network for users.
Scenario 1:
Scenario 2:
STEP-2: Repeater mode
Repeater Mode In this mode,you can extend the superior Wi-Fi signal by Repeater setting function under the Wireless column to increase the coverage of the wireless signal.
Scenario 1:
Scenario 2:
STEP-3: AP mode
AP mode connect the superior AP/Router by wire, you can transfer the superior's AP/Router wired signal into wireless signal.
Scenario 1:
Scenario 2:
Scenario 3:
Scenario 4:
STEP-4: WISP Mode
WISP Mode In this mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN.
Scenario 1:
FAQ Common problem
Q1: How to reset the CPE to factory default Settings?
Keep the CPE powered on, press the RESET button on CPE or Passive PoE box about 8 seconds, the CPE will restore to factory default settings.
Q2: What Can I do If I forgot the CPE’s Web Login User Name and Password?
In case you changed your CPE’s Login User Name and Password, we suggest you reset your CPE to factory default settings by above operations. Then use the following parameters to login the CPE’s Web interface:
Default IP address: 192.168.1.1
User Name: admin
Password: admin
It is suitable for: All TOTOLINK CPE |
Application introduction
After entering the management address of the CPE in the address bar of Chrome browser, the page cannot be displayed after entering the management password, as shown below.
Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password.
Set up steps
STEP-1: Change browser and clear browser cache
Try changing old version (before 72.0.3626.96) of Chrome browser or try other browser, such as Firefox, Internet Explorer, etc., and clear your browser cache. 
Delete cookies on the web browser. Here we take Firefox for example.
Note: In general, the browser enters the management address of the CPE and error pops up. Please use this method first.
STEP-2: Take CP900 as an example
2-1. CP900 default Gateway IP address 192.168.0.254:
Assigned manually IP address 192.168.0.x （“x” range from 2 to 253）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.254.
2-2. Enter 192.168.0.254 into the address bar of your browser. Log in the settings interface.
[Note]:
The default access address varies depending on the actual situation. Please find it on the bottom label of the product.
It is suitable for: All TOTOLINK CPE |
Preparation
l Before downloading files. please confirm the hardware version ofyour device and choose the corresponiding firmware version to uparade.
l Wrong firrmware version may damage your device and no warrante.
Set up steps
STEP-1: Guide for Hardware Version
For most TOTOLINK CPE, you can see two bar coded stickers at the front of the device, the character string started with Model No.(for example CP300) and ended with hardware Version (for example V2.0) is the serial number of your device. See below:
STEP-2:
Open browser, enter www.totolink.net Download the required files.
For example, if your hardware version is V2.0 , please download V2 version.
Note: If the hardware version is V1, V1 will be hidden.
STEP-3:
Unzip the file, correct upgrade file name is suffixed with ”web” or “bin” (except for some special models)
