Set up steps 

STEP-1: Connect your computer

Connect to the extender's LAN port with a network cable from a computer network port (or to search for and connect the  extender's wireless signal).

STEP-2: Assigned manually IP Address

TOTOLINK extender’s LAN IP address is 192.168.0.254, please type in IP address 192.168.0.x （“x” range from 2 to 250）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.254.

STEP-3: Enter 192.168.0.254 into the TOTOLINK extension in your browser. Take the EX200 as an example.

STEP-4: After setting up the extender successfully, please select Obtain an IP address automatically and Obtain DNS Server address automatically.

Note: Your terminal device must choose to obtain an IP address automatically to access the network.

Application introduction 

After entering the management address of the extender in the address bar of Chrome browser, the page cannot be displayed after entering the management password, as shown below.

Note: Ensure that the login IP address you typed in the address bar is correct, as well as the login username and password. 

Take EX200 as an example.

 Method One: login via PC 

STEP-1: Change browser and clear browser cache

Try changing old version (before 72.0.3626.96) of Chrome browser or try other browser, such as Firefox, Internet Explorer, etc., and clear your browser cache.

Delete cookies on the web browser. Here we take Firefox for example.

Note: In general, the browser enters the management address of the extender and error pops up. Please use this method first.

STEP-2: 

2-1. Extender default Gateway IP address 192.168.0.254:

Assigned manually IP address 192.168.0.x （“x” range from 2 to 253）, the Subnet Mask is 255.255.255.0 and Gateway is 192.168.0.254.

2-2. Enter 192.168.0.254 into the address bar of your browser. Log in the settings interface.

2-3. After setting up the extender successfully, please select Obtain an IP address automatically and Obtain DNS Server address automatically.

 Metod Two: login via tablet/Cellphone 

STEP-1: Change browser and clear browser cache

Try other browser, such as Firefox, Opera, etc., and clear your browser cache.

STEP-2: Enter 192.168.0.254 into the address bar of your browser. Log in the settings interface.

 Application introduction 

There are two methods to extend WiFi signal by Extender, you can setup the repeater function in the web-configuration interface or by pressing the WPS button. The second one is easy and fast.

Diagram

Set up steps 

STEP-1:

l Please make sure your router has WPS button before setting.

l Please confirm that your extender is in the factory state. If you are not sure, press the Reset button on the expander.

STEP-2:

1.Press the WPS button on the Router. There are two types of wireless router WPS buttons: RST/WPS button and WPS button. As shown below.

Note: If router is a RST/WPS button, no more than 5s, router will be reset to factory defaults if you press it for more than 5s.

2.Press the RST/WPS button on the EX200 for about 2~3s (not more than 5s, it will reset the extender to factory default if you press it for more than 5s) within 2 minutes after pressing the button on the router.

Note: The “extending” LED will flash when connecting and become solid light when connection is successful. If the “extending” LED is off lastly, it means that the WPS connection is fail.

STEP-3:

When it is fail to connect to the router by the WPS button, there are two suggestions we recommend for a successful connection.

1.Place EX200 near the router and power it on, and then connect with the router by the WPS button again. When connection is finished, unplug the EX200, and then you can replace the EX200 to the desired place.

2.Try to connect to the router by setting up in the extender’s web-configuration interface, please refer to method 2 in FAQ# (How to change SSID of EX200)

 Preparation 

l Before downloading files. please confirm the hardware version ofyour device and choose the corresponiding firmware version to uparade. 

l Wrong firrmware version may damage your device and no warrante.

 Set up steps 

STEP-1: Guide for Hardware Version

For most TOTOLINK extender, you can see two bar coded stickers at the front of the device, the character string started with Model No.(for example EX200) and ended with Hardware Version (for example V1.0) is the serial number of your device. See below:

STEP-2:

Open browser, enter www.totolink.net  Download the required files.

For example, if your hardware version is V2.0 , please download V2 version.

Note: If the hardware version is V1, V1 will be hidden.

STEP-3:

Unzip the file, correct upgrade file name is suffixed with ”web” or “bin” (except for some special models)